Heatbed

Sort By:  
  • Springs for Heatbed ()
    Description:

    Compression spring for heatbed.

     

    Specification:

    OD : Φ5.63mm
    Wire diameter : 0.63mm
    Total Coils : 10
    Free Length : 18mm

    Package list:

    4 x Springs for Heatbed

    Add to Cart
    RM10.00
    RM12.00
  • MK2B Heatbed Black (MK2A)

    MK2B Heatbed is the latest version for 12Vdc & 24Vdc power supply.

    Power Supply: 12Vdc/ 24Vdc

    Features :  

    1. Dimensions 214mm x 214mm
    2. Laminate FR4 1.6+-0.15mm
    3. 2 layer, 35μm copper
    4. Red Soldermask - both sides
    5. White Silkscreen - both sides
    6. Power Input: 12Vdc & 24Vdc
    7. Copper plated holes
    8. Resistance between 1-2 ohm

    Attention:

    Measured PCB copper heat resistance above about 1.5 ohms.

    1. If GEN4 with MOSFET drivers , you need to add a heat sink. According to the users experience , MOSFET without additional heat sink , heated continuous for about 10 minutes will burn the MOSFET . Recommended relay driver . Melzi and mightyboard without relays.

    2. Power consumption may be greater than 300W. Please check the full power of the power supply.

    3. size: 21.4 x 21.4cm, According to the Eagle file posted on Thingiverse, the M3 holes are spaced 209 mm

     

    The current rating of your power supply can never be too high - the board will draw as much current as it needs based on the voltage, but never more.

    That said, these boards have about 1 Ohm resistance. If you put 12v across something with 1 Ohm resistance, its going to try to draw 12A (Ohm's law says V=I*R, so 12V/1Ohm=12A).

    That means your 6A power supply isn't enough to handle one of these beds. That said, the resistance varies depending on where you get it. If you have a 2 Ohm unit, 6A is fine.

    Add to Cart
    RM88.00
    RM120.00
  • MK2A Heatbed Red (MK2A)

    MK2A Heatbed is the old version for 12Vdc power supply.

    Power Supply: 12Vdc

    Features :  

    1. Dimensions 214mm x 214mm
    2. Laminate FR4 1.6+-0.15mm
    3. 2 layer, 35μm copper
    4. Red Soldermask - both sides
    5. White Silkscreen - both sides
    6. Power Input: 12Vdc & 24Vdc
    7. Copper plated holes
    8. Resistance between 1-2 ohm

    Attention:

    Measured PCB copper heat resistance above about 1.5 ohms.

    1. If GEN4 with MOSFET drivers , you need to add a heat sink. According to the users experience , MOSFET without additional heat sink , heated continuous for about 10 minutes will burn the MOSFET . Recommended relay driver . Melzi and mightyboard without relays.

    2. Power consumption may be greater than 300W. Please check the full power of the power supply.

    3. size: 21.4 x 21.4cm, According to the Eagle file posted on Thingiverse, the M3 holes are spaced 209 mm

     

    The current rating of your power supply can never be too high - the board will draw as much current as it needs based on the voltage, but never more.

    That said, these boards have about 1 Ohm resistance. If you put 12v across something with 1 Ohm resistance, its going to try to draw 12A (Ohm's law says V=I*R, so 12V/1Ohm=12A).

    That means your 6A power supply isn't enough to handle one of these beds. That said, the resistance varies depending on where you get it. If you have a 2 Ohm unit, 6A is fine.

    Add to Cart
    RM75.00
    RM115.00
  • MK2B Heatbed (MK2B)

    MK2B Heatbed is the latest version for both 12V and 24V power supply.

    Power Supply: 12V or 24VDC

    LED and Resistor are mounted.
     

    Features :  

    1. Dimensions 214mm x 214mm
    2. Laminate FR4 1.6+-0.15mm
    3. 2 layer, 35μm copper
    4. Red Soldermask - both sides
    5. White Silkscreen - both sides
    6. Power Input: 12Vdc & 24Vdc
    7. Copper plated holes
    8. Resistance between 1-2 ohm

    Attention:

    Measured PCB copper heat resistance above about 1.5 ohms.

    1. If GEN4 with MOSFET drivers , you need to add a heat sink. According to the users experience , MOSFET without additional heat sink , heated continuous for about 10 minutes will burn the MOSFET . Recommended relay driver . Melzi and mightyboard without relays.

    2. Power consumption may be greater than 300W. Please check the full power of the power supply.

    3. size: 21.4 x 21.4cm, According to the Eagle file posted on Thingiverse, the M3 holes are spaced 209 mm

     

    The current rating of your power supply can never be too high - the board will draw as much current as it needs based on the voltage, but never more.

    That said, these boards have about 1 Ohm resistance. If you put 12v across something with 1 Ohm resistance, its going to try to draw 12A (Ohm's law says V=I*R, so 12V/1Ohm=12A).

    That means your 6A power supply isn't enough to handle one of these beds. That said, the resistance varies depending on where you get it. If you have a 2 Ohm unit, 6A is fine.

     

    Add to Cart
    RM85.00
    RM125.00
  • MK3 Heatbed Aluminium Core Black (MK3)
    • Brand: Reprap
    • Color: Black
    • Thickness: 3.2mm
    • Dimonsion: 214mm x 214mm
    • Resistance: Between 1.0 and 1.2 ohm
    • Heatup time: to 100 degrees Celsius less than 10min for both 12V and 24V
    • More Details:
      The Alu-Heatbed MK3 have features similar to MK2 and you can also operate this board with 12V or 24V.
      - Heatbed with 3.2mm Aluminum Core. Print directly on the heatbed, no need for glass plate. It's a much lighter solution than PCB heatbed + glass, which makes it better for faster prints.
      - Dual power supply. Operate at 12V or 24V. Your can use thinner wires when operating at 24V.
      - A central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole.
      - large solder pads for multiple wires (ribbon cable) or a SMD pinhead connector can be mounted.
      - Pads for SMD thermistor 1206
      - 1 layer 35um (1oz base) copper
    • Package Includes:
      1 x MK3 Heatbed with 3.2mm Aluminum Core
    Add to Cart
    RM120.00
    RM150.00
  • Rostock Delta Heatbed Aluminium Core Black (MK3)
    • Brand: Reprap
    • Color: Black
    • Thickness: 3.2mm
    • Dimension: 265mm
    • Resistance: Between 1.0 and 1.2 ohm
    • Heatup time: to 100 degrees Celsius less than 10min for both 12V and 24V
    • More Details:
      The Alu-Heatbed MK3 have features similar to MK2 and you can also operate this board with 12V or 24V.
      - Heatbed with 3.2mm Aluminum Core. Print directly on the heatbed, no need for glass plate. It's a much lighter solution than PCB heatbed + glass, which makes it better for faster prints.
      - Dual power supply. Operate at 12V or 24V. Your can use thinner wires when operating at 24V.
      - A central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole.
      - large solder pads for multiple wires (ribbon cable) or a SMD pinhead connector can be mounted.
      - Pads for SMD thermistor 1206
      - 1 layer 35um (1oz base) copper
    • Package Includes:
      1 x MK3 Heatbed with 3.2mm Aluminum Core
    Add to Cart
    RM165.00
    RM240.00
  • Rostock Delta Heatbed Aluminium Core Black (MK3)
    • Brand: Reprap
    • Color: Black
    • Thickness: 3.2mm
    • Dimension: Diameter 220mm
    • Resistance: Between 1.0 and 1.2 ohm
    • Heatup time: to 100 degrees Celsius less than 10min for both 12V and 24V
    • More Details:
      The Alu-Heatbed MK3 have features similar to MK2 and you can also operate this board with 12V or 24V.
      - Heatbed with 3.2mm Aluminum Core. Print directly on the heatbed, no need for glass plate. It's a much lighter solution than PCB heatbed + glass, which makes it better for faster prints.
      - Dual power supply. Operate at 12V or 24V. Your can use thinner wires when operating at 24V.
      - A central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole.
      - large solder pads for multiple wires (ribbon cable) or a SMD pinhead connector can be mounted.
      - Pads for SMD thermistor 1206
      - 1 layer 35um (1oz base) copper
    • Package Includes:
      1 x MK3 Heatbed with 3.2mm Aluminum Core
    Add to Cart
    RM155.00
    RM220.00
Per Page      1 - 7 of 7

Powered by Abantecart eCommerce Solution