3D Printer & Kits

3dprinter.my store is the leading 3D Printer provider, offering largest choice of personal 3D printer products, affordable 3d printer with shipping worldwide.
Sort By:  
  • Prusa i2 Fully Assembled & Calibrated (Prusa i2)
    The Prusa Mendel Iteration 2 is an improvement of the Prusa Mendel (iteration 1), and was released in November 2011.

    The Prusa Mendel is currently the BEST open source 3D printer design with enough testing behind it to prove its worth (over 3 years). This combined with the latest improvements to the design(e.g. gregs modified wade extruder cold end) means that you will be able to assemble this printer and pretty much start printing as soon as the printer is ready to go.

    It is easy to assemble and maintain, and produces high quality printed results. The Prusa Mendel is the current best of breed RepRap 3D printer. It is easy to assemble and maintain, and produces high quality printed results.

    We have made some improvements to the standard Prusa Mendel RepRap design, to further improve print quality and reliability:
    This complete Mendel Prusa kits has everything you need to assemble your 3D printer with a printing envelope of 200x200x110mm.


    This is a complete kit for a Prusa Mendel i2 printer With Greg's Hinged Accessible Extruder.

    The Prusa Mendel i2 uses LM8UU Linear bearings instead of printed bushings for a better print quality and since there is no gluing required for the Prusa Mendel i2 the building process is much easier compared to a regular Prusa.

    The printer is also build with an aluminum bottom plate. This is better for alignment and also for safety. All the parts are high quality parts especially the printed parts.
    Add to Cart
    RM2,399.00
  • Reprap 3D Printer Prusa i2 Full Kit (Prusa i2)
    The Prusa Mendel Iteration 2 is an improvement of the Prusa Mendel (iteration 1), and was released in November 2011.

    The Prusa Mendel is currently the BEST open source 3D printer design with enough testing behind it to prove its worth (over 3 years). This combined with the latest improvements to the design(e.g. gregs modified wade extruder cold end) means that you will be able to assemble this printer and pretty much start printing as soon as the printer is ready to go.

    It is easy to assemble and maintain, and produces high quality printed results. The Prusa Mendel is the current best of breed RepRap 3D printer. It is easy to assemble and maintain, and produces high quality printed results.

    We have made some improvements to the standard Prusa Mendel RepRap design, to further improve print quality and reliability:
    This complete Mendel Prusa kits has everything you need to assemble your 3D printer with a printing envelope of 200x200x110mm.

    This kit derives from the Prusa i2 and comes with Lm8UU linearing bearing for this price.

    We provide you with the smooth and threaded rods already cutted, all the plastic and metal parts needed.

    This kit contains:

        plastic parts
        smooth and threaded rods
        Stainless steel reinforced belts
        stepper motors
        eletronics
        bolts, nut, washer, bearings...
        extruder
        hot end
        end stops
        Mezli board
        Heater print bed
        alu print bed base

    To assemble this kit you need to have basic soldering skills, you should be able to assemble this over a weekend.

    The waiting time for the shipment of this kit is usually 2 to 3 days. Just the time of printing the parts.
    Add to Cart
    RM1,799.00
  • Reprap Rostock Mini Kit (Rostock Mini)
    The Rostock mini is a delta 3D printer based on the modified design of the original Rostock created by Johann. The printer is designed to have a smaller build volume allowing for a smaller, more compact, portable, and desktop friendly version of the delta RepRap design.

    Please refer to http://reprap.org/wiki/Rostock_mini  for more information about Rostock Mini 3D Printer.
     

    Bill of Materials

    Printed Parts

    • Motor end x 3
    • Idler end x 3
    • Carriage x 3
    • U-joints x 12
    • Jaws x 12
    • Platform x 1
    • Hotend mount x 1
    • Fan mount x 1
    • Extruder x 1

    Laser Cut Parts

    • Lower frame x 1 - 6mm acrylic
    • Upper frame x 1 - 6mm acrylic
    • Printbed insulator x 1 - 1/8" plywood
    • NEMA17 gaskets x 3 - 1/8" plywood

    Electro-mechanical

    • NEMA17s x 3
    • 608ZZ ball bearings x 6
    • LM8UU linear bearings x 6
    • 36tooth GT2 timing pulley x 3
    • GT2 timing belt x 3
    • Subminiature switch x 3
    • Ramps 1.4 controller x 1
    • 200 x 200mm heated printbed x 1
    • Groovemount hotend x 1
    • 40mm cooling fan x 1
    • N-channel MOSFET x 1

    Hardware

    • M2.5x10 x 6
    • M3x10 x 7 - flathead
    • M3x12 x 76
    • M3x16 x 12
    • M3 fender washer x 30
    • M3 washer x 40
    • M3 nuts x 56
    • M4x16 x 20
    • M4 washer x 20
    • M4 nuts x 4
    • M8x30 x 3
    • M8 washer x 6
    • M8 nuts x 3
    • 8mm precision ground rod x 6
    • 0.188" OD rigid carbon fiber tube x 6
    • 6"x6" 3/16" thick borosilicate glass
    Add to Cart
    RM1,950.00
  • Reprap Prusa i3 All Laser Cut Fully Assembled & Calibrated (Prusa i3)
    This is the best 3d printer you can get in the market now. With very fine print resolution and very steady and firm Frame Assembly. Loaded with latest firmware and it prints like star ship!

    3dprinter.my i3 printer kit is an open source 3d printer kit based on prusa i3, with the Melzi/ Arduino  electronics and H-Extruer and with major improvements with High Printer Z, 160mm!

    Host software: Repetier-host or Pronterface

    Firmware: Sprinter - Melzi in the package is ready to use, you do not need to do anything to the firmware.

    Build volume: X200 x Y180 x Z160mm

    Overall size: 420x420x380mm

    Printing materials: ABS, PLA, 3mm or 1.75mm diameter thermoplastic.

    Build surface: PCB-heated bed to reduce complexity of assembly and to ensure parts do not warp.

    Computer interface: USB

    Motion: Linear ball bearings on X and Y and Z axes

    Pre-soldered electronics with built-in microSD card slot for standalone printing.

    Enhancements to the printed parts to improve the ease of assembly.

    Pre-order available. Delivery 1weeks.
    LCD Display and SD Card Reader - Add on Rm350.00


    See the printer printing in Action!
    See 300mm/sec Super Fast Printing Speed with High Resolution with this Printer!
    Add to Cart
    RM3,650.00
  • Prusa i3 Full Kit Laser Cut Acrylic Black (Prusa i3)
    Product Description 

    The Prusa i3 (iteration 3) is the newest and current 3D Printer design by RepRap Core Developer Prusajr. The i3 incorporates lessons learned from the previous two Prusa designs, as well as other popular modern RepRap designs. Compared to its predecessors and other RepRap machines, Prusa i3 is known for its extreme ease of assembling, reliable printing, and dual extruder option. This printer uses laser-cut acrylic sheets to improve stability.

    Prusa i3 Build Documents 

    Click here for Prusa i3 build manual by 3printer.my
    Click here for Prusa i3 STL files
    Click here for Prusa i3 RAMPS
    Click here for Prusa ALC i3 Firmware

    Prusa i3 Technical Details


    Build Volume  X200mm Y200mm x Z190mm  (X8″ x Y8″ x Z7.5″)
    Overall size 420x420x380mm
    Control Board RAMPS 1.4 Electronics
    Frame
     5mm Acrylic Black
    Hotend 0.4mm J-head MK IV
    50 micron Layer Height achievable
    MK2A Heated Build Platform
    GT2 Pulley’s and Belts
    12V 30A Power Supply
    H Extruder


    Included in our Prusa i3 Package 

    MK2A Heated Built Platform (wires and LED pre-soldered)
    Nema 17 Stepper Motors x 5 (connectors and pins also included)
    12V 30A Power Supply
    RAMPS 1.4 Shield
    Mega 2560 R3 Control Board
    Pololu Stepper Driver x 4 (with heat sinks)

    Prusa i3 Linear Motion 

    GT2 20-Tooth Aluminum Pulleys x 2
    GT2 Timing Belt 1.9m
    Hardened Stainless Steel Precision Rods
    LM8UU Bearings x 10

    Prusa i3 Tool Kit 

    3m Measuring Tape
    Allen Wrench Set
    14mm Wrench
    Circular File
    Needle-nose Pliers

    Miscellaneous 

    4mm x 210mm x 200mm Borosilicate Glass plate
    MKIV J-head hotend (3.0mm with 0.4mm orifice)

    Host software: Pronterface

    Firmware: Marlin - RAMPS in the package is ready to use, you do not need to do anything to the firmware

    Printing materials: ABS, PLA, 3mm or 1.75mm diameter thermoplastic.

    Build surface: PCB-heated bed to reduce complexity of assembly and to ensure parts do not warp.

    Computer interface: USB


    1st & 2nd batch of Fully Assembled & Calibrated WLC i3 (10units) all sold out and supported by us during installation easily. All the 10 units out in our client hands are able to give very fine print of single layer wall 0.5mm up to 190mm high! All of 10units 3d printer are able to print within 1st hour out from the box without any problem!

    Thanks to all your support!

    Now we are launching the 3rd batch of Fully Assembled & Calibrated LC i3. So grab yours today to avoid any waiting!
    Add to Cart
    RM1,850.00
    RM2,100.00
  • Prusa i3 Full Kit Laser Cut Acrylic Orange (Prusa i3)
    Product Description 

    The Prusa i3 (iteration 3) is the newest and current 3D Printer design by RepRap Core Developer Prusajr. The i3 incorporates lessons learned from the previous two Prusa designs, as well as other popular modern RepRap designs. Compared to its predecessors and other RepRap machines, Prusa i3 is known for its extreme ease of assembling, reliable printing, and dual extruder option. This printer uses laser-cut acrylic sheets to improve stability.

    Prusa i3 Build Documents 

    Click here for Prusa i3 build manual by 3printer.my
    Click here for Prusa i3 STL files
    Click here for Prusa i3 RAMPS
    Click here for Prusa ALC i3 Firmware


    Prusa i3 Technical Details

    Build Volume
     X200mm x Y200mm x Z190mm  (X8″ x Y8″ x Z7.48″)
    Overall size 420x420x380mm
    Control Board RAMPS 1.4 Electronics
    Frame
     6mm Acrylic Orange
    Hotend 0.4mm J-head MK IV
    50 micron Layer Height achievable
    MK2A Heated Build Platform
    GT2 Pulley’s and Belts
    12V 30A Power Supply
    H Extruder


    Included in our Prusa i3 Package 

    MK2A Heated Built Platform (wires and LED pre-soldered)
    Nema 17 Stepper Motors x 5 (connectors and pins also included)
    12V 30A Power Supply
    RAMPS 1.4 Shield
    Mega 2560 R3 Control Board
    Pololu Stepper Driver x 4 (with heat sinks)

    Prusa i3 Linear Motion 

    GT2 20-Tooth Aluminum Pulleys x 2
    GT2 Timing Belt 1.9m
    Hardened Stainless Steel Precision Rods
    LM8UU Bearings x 10

    Prusa i3 Tool Kit 

    3m Measuring Tape
    Allen Wrench Set
    14mm Wrench
    Circular File
    Needle-nose Pliers

    Miscellaneous 

    4mm x 210mm x 200mm Borosilicate Glass plate
    MKIV J-head hotend (3.0mm with 0.4mm orifice)

    Host software: Pronterface

    Firmware: Marlin - RAMPS in the package is ready to use, you do not need to do anything to the firmware

    Printing materials: ABS, PLA, 3mm or 1.75mm diameter thermoplastic.

    Build surface: PCB-heated bed to reduce complexity of assembly and to ensure parts do not warp.

    Computer interface: USB


    1st & 2nd batch of Fully Assembled & Calibrated WLC i3 (10units) all sold out and supported by us during installation easily. All the 10 units out in our client hands are able to give very fine print of single layer wall 0.5mm up to 190mm high! All of 10units 3d printer are able to print within 1st hour out from the box without any problem!

    Thanks to all your support!

    Now we are launching the 3rd batch of Fully Assembled & Calibrated LC i3. So grab yours today to avoid any waiting!
    Add to Cart
    RM1,900.00
    RM2,150.00
  • Prusa i3 Full Kit Laser Cut Acrylic Petronas Green (Prusa i3)
    Product Description 

    The Prusa i3 (iteration 3) is the newest and current 3D Printer design by RepRap Core Developer Prusajr. The i3 incorporates lessons learned from the previous two Prusa designs, as well as other popular modern RepRap designs. Compared to its predecessors and other RepRap machines, Prusa i3 is known for its extreme ease of assembling, reliable printing, and dual extruder option. This printer uses laser-cut acrylic sheets to improve stability.

    Prusa i3 Build Documents 

    Click here for Prusa i3 build manual by 3printer.my
    Click here for Prusa i3 STL files
    Click here for Prusa i3 RAMPS
    Click here for Prusa ALC i3 Firmware


    Prusa i3 Technical Details

    Build Volume
     X200mm x Y200mm x Z190mm  (X8″ x Y8″ x Z7.5″)
    Overall size 420x420x380mm
    Control Board RAMPS 1.4 Electronics
    Frame 
    6mm Acrylic Petronas Green
    Hotend 0.4mm J-head MK IV
    50 micron Layer Height achievable
    MK2A Heated Build Platform
    GT2 Pulley’s and Belts
    12V 30A Power Supply
    H Extruder


    Included in our Prusa i3 Package 

    MK2A Heated Built Platform (wires and LED pre-soldered)
    Nema 17 Stepper Motors x 5 (connectors and pins also included)
    12V 30A Power Supply
    RAMPS 1.4 Shield
    Mega 2560 R3 Control Board
    Pololu Stepper Driver x 4 (with heat sinks)

    Prusa i3 Linear Motion 

    GT2 20-Tooth Aluminum Pulleys x 2
    GT2 Timing Belt 1.9m
    Hardened Stainless Steel Precision Rods
    LM8UU Bearings x 10

    Prusa i3 Tool Kit 

    3m Measuring Tape
    Allen Wrench Set
    14mm Wrench
    Circular File
    Needle-nose Pliers

    Miscellaneous 

    4mm x 210mm x 200mm Borosilicate Glass plate
    MKIV J-head hotend (3.0mm with 0.4mm orifice)

    Host software: Pronterface

    Firmware: Marlin - RAMPS in the package is ready to use, you do not need to do anything to the firmware

    Printing materials: ABS, PLA, 3mm or 1.75mm diameter thermoplastic.

    Build surface: PCB-heated bed to reduce complexity of assembly and to ensure parts do not warp.

    Computer interface: USB


    1st & 2nd batch of Fully Assembled & Calibrated WLC i3 (10units) all sold out and supported by us during installation easily. All the 10 units out in our client hands are able to give very fine print of single layer wall 0.5mm up to 190mm high! All of 10units 3d printer are able to print within 1st hour out from the box without any problem!

    Thanks to all your support!

    Now we are launching the 3rd batch of Fully Assembled & Calibrated LC i3. So grab yours today to avoid any waiting!
    Add to Cart
    RM1,900.00
    RM2,150.00
  • Prusa i3 Full Kit Laser Cut Acrylic Transparent (Prusa i3)
    Product Description 

    The Prusa i3 (iteration 3) is the newest and current 3D Printer design by RepRap Core Developer Prusajr. The i3 incorporates lessons learned from the previous two Prusa designs, as well as other popular modern RepRap designs. Compared to its predecessors and other RepRap machines, Prusa i3 is known for its extreme ease of assembling, reliable printing, and dual extruder option. This printer uses laser-cut acrylic sheets to improve stability.

    Prusa i3 Build Documents 

    Click here for Prusa i3 build manual by 3printer.my
    Click here for Prusa i3 STL files
    Click here for Prusa i3 RAMPS
    Click here for Prusa ALC i3 Firmware


    Prusa i3 Technical Details

    Build Volume
     X200mm x Y200mm x Z190mm  (X8″ x Y8″ x Z7.5″)
    Overall size 420x420x380mm
    Control Board RAMPS 1.4 Electronics
    Frame 
    6mm Acrylic Transparent Clear
    Hotend 0.4mm J-head MK IV
    50 micron Layer Height achievable
    MK2A Heated Build Platform
    GT2 Pulley’s and Belts
    12V 30A Power Supply
    H Extruder


    Included in our Prusa i3 Package 

    MK2A Heated Built Platform (wires and LED pre-soldered)
    Nema 17 Stepper Motors x 5 (connectors and pins also included)
    12V 30A Power Supply
    RAMPS 1.4 Shield
    Mega 2560 R3 Control Board
    Pololu Stepper Driver x 4 (with heat sinks)

    Prusa i3 Linear Motion 

    GT2 20-Tooth Aluminum Pulleys x 2
    GT2 Timing Belt 1.9m
    Hardened Stainless Steel Precision Rods
    LM8UU Bearings x 10

    Prusa i3 Tool Kit 

    3m Measuring Tape
    Allen Wrench Set
    14mm Wrench
    Circular File
    Needle-nose Pliers

    Miscellaneous 

    4mm x 210mm x 200mm Borosilicate Glass plate
    MKIV J-head hotend (3.0mm with 0.4mm orifice)

    Host software: Pronterface

    Firmware: Marlin - RAMPS in the package is ready to use, you do not need to do anything to the firmware

    Printing materials: ABS, PLA, 3mm or 1.75mm diameter thermoplastic.

    Build surface: PCB-heated bed to reduce complexity of assembly and to ensure parts do not warp.

    Computer interface: USB


    1st & 2nd batch of Fully Assembled & Calibrated WLC i3 (10units) all sold out and supported by us during installation easily. All the 10 units out in our client hands are able to give very fine print of single layer wall 0.5mm up to 190mm high! All of 10units 3d printer are able to print within 1st hour out from the box without any problem!

    Thanks to all your support!

    Now we are launching the 3rd batch of Fully Assembled & Calibrated LC i3. So grab yours today to avoid any waiting!
    Add to Cart
    RM2,150.00
  • Prusa i3 Full Kit Laser Cut Acrylic White (Prusa i3)
    Product Description 

    The Prusa i3 (iteration 3) is the newest and current 3D Printer design by RepRap Core Developer Prusajr. The i3 incorporates lessons learned from the previous two Prusa designs, as well as other popular modern RepRap designs. Compared to its predecessors and other RepRap machines, Prusa i3 is known for its extreme ease of assembling, reliable printing, and dual extruder option. This printer uses laser-cut acrylic sheets to improve stability.

    Prusa i3 Build Documents 

    Click here for Prusa i3 build manual by 3printer.my
    Click here for Prusa i3 STL files
    Click here for Prusa i3 RAMPS
    Click here for Prusa ALC i3 Firmware


    Prusa i3 Technical Details

    Build Volume
     X200mm x Y200mm x Z190mm  (X8″ x Y8″ x Z7.5″)
    Overall size 420x420x380mm
    Control Board RAMPS 1.4 Electronics
    Frame
     5mm Acrylic White
    Hotend 0.4mm J-head MK IV
    50 micron Layer Height achievable
    MK2A Heated Build Platform
    GT2 Pulley’s and Belts
    12V 30A Power Supply
    H Extruder


    Included in our Prusa i3 Package 

    MK2A Heated Built Platform (wires and LED pre-soldered)
    Nema 17 Stepper Motors x 5 (connectors and pins also included)
    12V 30A Power Supply
    RAMPS 1.4 Shield
    Mega 2560 R3 Control Board
    Pololu Stepper Driver x 4 (with heat sinks)

    Prusa i3 Linear Motion 

    GT2 20-Tooth Aluminum Pulleys x 2
    GT2 Timing Belt 1.9m
    Hardened Stainless Steel Precision Rods
    LM8UU Bearings x 10

    Prusa i3 Tool Kit 

    3m Measuring Tape
    Allen Wrench Set
    14mm Wrench
    Circular File
    Needle-nose Pliers

    Miscellaneous 

    4mm x 210mm x 200mm Borosilicate Glass plate
    MKIV J-head hotend (3.0mm with 0.4mm orifice)

    Host software: Pronterface

    Firmware: Marlin - RAMPS in the package is ready to use, you do not need to do anything to the firmware

    Printing materials: ABS, PLA, 3mm or 1.75mm diameter thermoplastic.

    Build surface: PCB-heated bed to reduce complexity of assembly and to ensure parts do not warp.

    Computer interface: USB


    1st & 2nd batch of Fully Assembled & Calibrated WLC i3 (10units) all sold out and supported by us during installation easily. All the 10 units out in our client hands are able to give very fine print of single layer wall 0.5mm up to 190mm high! All of 10units 3d printer are able to print within 1st hour out from the box without any problem!

    Thanks to all your support!

    Now we are launching the 3rd batch of Fully Assembled & Calibrated LC i3. So grab yours today to avoid any waiting!
    Add to Cart
    RM1,850.00
    RM2,100.00
  • Prusa i3 Full Kit Laser Cut Wood (Prusa i3)
    Product Description 

    The Prusa i3 (iteration 3) is the newest and current 3D Printer design by RepRap Core Developer Prusajr. The i3 incorporates lessons learned from the previous two Prusa designs, as well as other popular modern RepRap designs. Compared to its predecessors and other RepRap machines, Prusa i3 is known for its extreme ease of assembling, reliable printing, and dual extruder option. This printer uses laser-cut acrylic sheets to improve stability.

    Prusa i3 Build Documents 

    Click here for Prusa i3 build manual by 3printer.my
    Click here for Prusa i3 STL files
    Click here for Prusa i3 RAMPS
    Click here for Prusa ALC i3 Firmware


    Prusa i3 Technical Details

    Build Volume
     X200mm x Y200mm x Z190mm  (X8″ x Y8″ x Z7.5″)
    Overall size 420x420x380mm
    Control Board RAMPS 1.4 Electronics
    Frame
     5mm Plywood
    Hotend 0.4mm J-head MK IV
    50 micron Layer Height achievable
    MK2A Heated Build Platform
    GT2 Pulley’s and Belts
    12V 30A Power Supply
    H Extruder


    Included in our Prusa i3 Package 

    MK2A Heated Built Platform (wires and LED pre-soldered)
    Nema 17 Stepper Motors x 5 (connectors and pins also included)
    12V 30A Power Supply
    RAMPS 1.4 Shield
    Mega 2560 R3 Control Board
    Pololu Stepper Driver x 4 (with heat sinks)

    Prusa i3 Linear Motion 

    GT2 20-Tooth Aluminum Pulleys x 2
    GT2 Timing Belt 1.9m
    Hardened Stainless Steel Precision Rods
    LM8UU Bearings x 10

    Prusa i3 Tool Kit 

    3m Measuring Tape
    Allen Wrench Set
    14mm Wrench
    Circular File
    Needle-nose Pliers

    Miscellaneous 

    4mm x 210mm x 200mm Borosilicate Glass plate
    MKIV J-head hotend (3.0mm with 0.4mm orifice)

    Host software: Pronterface

    Firmware: Marlin - RAMPS in the package is ready to use, you do not need to do anything to the firmware

    Printing materials: ABS, PLA, 3mm or 1.75mm diameter thermoplastic.

    Build surface: PCB-heated bed to reduce complexity of assembly and to ensure parts do not warp.

    Computer interface: USB


    1st & 2nd batch of Fully Assembled & Calibrated WLC i3 (10units) all sold out and supported by us during installation easily. All the 10 units out in our client hands are able to give very fine print of single layer wall 0.5mm up to 190mm high! All of 10units 3d printer are able to print within 1st hour out from the box without any problem!

    Thanks to all your support!

    Now we are launching the 3rd batch of Fully Assembled & Calibrated LC i3. So grab yours today to avoid any waiting!
    Add to Cart
    RM1,750.00
    RM1,950.00
  • Reprap 3D Printer Prusa i3 Fully Assembled & Calibrated (Prusa i3)
    Product Description

    The Prusa i3 (iteration 3) is the newest and current 3D Printer design by RepRap Core Developer Prusajr. The i3 incorporates lessons learned from the previous two Prusa designs, as well as other popular modern RepRap designs. Compared to its predecessors and other RepRap machines, Prusa i3 is known for its extreme ease of assembling, reliable printing, and dual extruder option. This printer uses laser-cut acrylic sheets to improve stability.

    Prusa i3 Build Documents 

    Click here for Prusa i3 build manual by 3printer.my
    Click here for Prusa i3 STL files
    Click here for Prusa i3 RAMPS
    Click here for Prusa ALC i3 Firmware


    Prusa i3 Technical Details

    Build Volume
     X200mm x Y200mm x Z190mm  (X8″ x Y8″ x Z7.5″)
    Overall size 420x420x380mm
    Control Board RAMPS 1.4 Electronics
    Frame
    6mm Acrylic Sheets
    Hotend 0.4mm J-head MK IV
    50 micron Layer Height achievable
    MK2A Heated Build Platform
    GT2 Pulley’s and Belts
    12V 30A Power Supply
    H Extruder


    Included in our Prusa i3 Package 

    MK2A Heated Built Platform (wires and LED pre-soldered)
    Nema 17 Stepper Motors x 5 (connectors and pins also included)
    12V 30A Power Supply
    RAMPS 1.4 Shield
    Mega 2560 R3 Control Board
    Pololu Stepper Driver x 4 (with heat sinks)

    Prusa i3 Linear Motion

    GT2 20-Tooth Aluminum Pulleys x 2
    GT2 Timing Belt 1.9m
    Hardened Stainless Steel Precision Rods
    LM8UU Bearings x 10

    Prusa i3 Tool Kit

    3m Measuring Tape
    Allen Wrench Set
    14mm Wrench
    Circular File
    Needle-nose Pliers

    Miscellaneous

    4mm x 210mm x 200mm Borosilicate Glass plate
    MKIV J-head hotend (3.0mm with 0.4mm orifice)

    Host software: Pronterface

    Firmware: Marlin - RAMPS in the package is ready to use, you do not need to do anything to the firmware

    Printing materials: ABS, PLA, 3mm or 1.75mm diameter thermoplastic.

    Build surface: PCB-heated bed to reduce complexity of assembly and to ensure parts do not warp.

    Computer interface: USB


    1st & 2nd batch of Fully Assembled & Calibrated WLC i3 (10units) all sold out and supported by us during installation easily. All the 10 units out in our client hands are able to give very fine print of single layer wall 0.5mm up to 190mm high! All of 10units 3d printer are able to print within 1st hour out from the box without any problem!

    Thanks to all your support!

    Now we are launching the 3rd batch of Fully Assembled & Calibrated LC i3. So grab yours today to avoid any waiting!
    Add to Cart
    RM2,450.00
    RM2,650.00
Per Page      1 - 11 of 11

Powered by Abantecart eCommerce Solution